cev.fr
USER’S MANUAL Kaleido-ALTO/QUAD | 9 Remaining time counter: The remaining time counter is identified by the hourglass icon: see figure 3.12 below
USER’S MANUAL 10 | Kaleido-ALTO/QUAD The next panel is the Video status. Listed here are the type and format of all video inputs connected to the u
USER’S MANUAL Kaleido-ALTO/QUAD | 11 The GPI status panel lists the active GPI inputs connected to the unit, and the status of the GPI outputs.. Th
USER’S MANUAL 12 | Kaleido-ALTO/QUAD Date/Time is where you set the internal time reference. Start by setting the Time zone that you wish to use fo
USER’S MANUAL Kaleido-ALTO/QUAD | 13 In either case, a window will open allowing you to set the error detection parameters. The window header will i
USER’S MANUAL 14 | Kaleido-ALTO/QUAD Figure 4.12 Kaleido-Alto/Quad ID panel Output Configuration must be set according to your display devic
USER’S MANUAL Kaleido-ALTO/QUAD | 15 You may also choose to output a color bars test pattern at the MWO-HDM or MWO-SDM output: check the Color Bars
USER’S MANUAL 16 | Kaleido-ALTO/QUAD selected for a communication port, the other protocol is not available on other ports as only one communication
USER’S MANUAL Kaleido-ALTO/QUAD | 17 Disable Actions opens the Action Settings window, showing the Actions Enabled checkbox. Unchecking this box dis
USER’S MANUAL 18 | Kaleido-ALTO/QUAD so it will be the most useful choice in most operational situations. A computer keyboard may only be located ne
USER’S MANUAL Kaleido-ALTO/QUAD Table of Contents 1 Kaleido-Alto and Kaleido-Quad User’s Manual...
USER’S MANUAL Kaleido-ALTO/QUAD | 19 Alphanumeric Group The alphanumeric buttons are used to type text in the name bar of a monitor or to enter ID n
USER’S MANUAL 20 | Kaleido-ALTO/QUAD Key Kaleido RCP equivalent Esc: Escape Tab: Select Enter: Enter CTRL+A: Input CTRL+F: Full Screen CT
USER’S MANUAL Kaleido-ALTO/QUAD | 21 In this mode, the only active controls are the Preset Layout selection buttons 1 to 10. The same layout number
USER’S MANUAL 22 | Kaleido-ALTO/QUAD Once you have selected all the monitors you wish to adjust, perform the adjustment (underscan/overscan or aspec
USER’S MANUAL Kaleido-ALTO/QUAD | 23 6 Channels, Layouts and Alarms Management The channels, layouts and alarm conditions are defined using the K-
USER’S MANUAL 24 | Kaleido-ALTO/QUAD The Andromeda controller may be set to a different BaudRate. In this case, it is possible to change the default
USER’S MANUAL Kaleido-ALTO/QUAD | 25 Baudrate To modify the Baudrate, just change the 9600 to, for example, 38400: Old line: <prop name="AN
USER’S MANUAL 26 | Kaleido-ALTO/QUAD 6- The operation is finished; close your ftp session by typing “bye”. 7- Now reboot the Alto/Quad so that t
USER’S MANUAL Kaleido-ALTO/QUAD | 27 8.1 Commands Many commands can be sent to the Kaleido-Alto/Quad via TCP/IP. Following is a list of these comm
USER’S MANUAL 28 | Kaleido-ALTO/QUAD LayoutToLoad is the name of the Layout to load. This Layout must have been exported to the Kaleido-Alto/Quad pr
USER’S MANUAL 2 | Kaleido-ALTO/QUAD 2 Kaleido-Alto/Quad System Concepts 2.1 Software Components There are two software components associated with
USER’S MANUAL Kaleido-ALTO/QUAD | 29 setKIcontrolMode This command is used to enable the Alto/Quad to key the detected mouse colors on video. <s
USER’S MANUAL 30 | Kaleido-ALTO/QUAD Open the Hyper Terminal software on another computer; from the “Program” menu choose “Accessories”, “Communicat
USER’S MANUAL Kaleido-ALTO/QUAD | 31 Two new fields will appear: in the “Host address” field enter the IP address of your Kaleido-Alto/Quad, and in
USER’S MANUAL 32 | Kaleido-ALTO/QUAD If the Kaleido-Alto/Quad receives the command and recognizes it, it will respond with the following: If th
USER’S MANUAL Kaleido-ALTO/QUAD | 33 8.2.1 Three Kaleido-Alto/Quads Open the HyperTerminal software on another computer; from the “Program” menu c
USER’S MANUAL 34 | Kaleido-ALTO/QUAD Two new fields will appear: in the “Host address” field enter the IP address of the first Kaleido-Alto/Quad, an
USER’S MANUAL Kaleido-ALTO/QUAD | 35 Commands can be sent to the Kaleido-Alto/Quad while a session is open. There is no maximum number of commands
USER’S MANUAL 36 | Kaleido-ALTO/QUAD If the Kaleido-Alto/Quad receives the command and recognizes it, it will respond with the following: If th
USER’S MANUAL Kaleido-ALTO/QUAD | 37 In each of the HyperTerminals, open a session with the associated Kaleido-Alto/Quad. The three Kaleido-Alt
USER’S MANUAL 38 | Kaleido-ALTO/QUAD When no more commands need to be sent to the Kaleido-Alto/Quad, close the connection using the closeID comman
USER’S MANUAL Kaleido-ALTO/QUAD | 3 3 Getting Started with the Kaleido-Alto/Quad 3.1 Quick Tour of the System Once the Kaleido-Alto/Quad is prope
USER’S MANUAL 4 | Kaleido-ALTO/QUAD Figure 3.2 Elements of the toolbar The K-Alto or K-Quad button contains a sub-menu showing the system para
USER’S MANUAL Kaleido-ALTO/QUAD | 5 3.3 Using a Layout In this section you will learn how to “use” the layout and understand the different paramete
USER’S MANUAL 6 | Kaleido-ALTO/QUAD Note: you can see at a glance which channel is assigned to which monitor by clicking the Tab key on the SIP key
USER’S MANUAL Kaleido-ALTO/QUAD | 7 of the video signal; the choice of decoding filter - Adaptive, Temporal or Spatial – depends highly on the con
USER’S MANUAL 8 | Kaleido-ALTO/QUAD Figure 3.9 Clock Settings window Note that when using the internal reference time, the correct time of d
Commentaires sur ces manuels